Nowadays, the use of bathtubs is very popular. Many family bathrooms have bathtubs. In the modern fast-paced and high-stress life, the best way to relieve fatigue and relax is to take a hot bath in the bathtub. Yes, the bathtub does bring us infinite comfort.
bathtub cleaning
First, the maintenance method of the bathtub
1. The daily cleaning of the bathtub can be done with general liquid detergent and soft cloth, not with ketone or chlorine water. When disinfecting, disinfectants containing formic acid and formaldehyde are prohibited.
2. If there are scratches or cigarette burns on the surface of the bathtub, just use 2000# water abrasive paper to polish it, then apply toothpaste, and polish it with a soft cloth to make it as clean as new.
3. The scale on the surface of the bathtub can be wiped with a soft towel dipped in a mildly acidic detergent, such as lemon juice and vinegar.
Bathtub cleaning and maintenance
4. Clean the hydraulic friction device: fill the bathtub with 40°C hot water, add detergent at a dose of 2 grams per liter, start the hydro massage for about 5 minutes, stop the pump to drain water, then fill up with cold water, start the hydro massage for about 3 minutes, stop After the pump drains and cleans the tub.
5. If the surface of the cylinder body is dirty, it can be wiped with a wet towel dipped in a neutral detergent. This process can be repeated three times, and it will be as clean as new.
6. Do not use hard objects or knives to strike and scratch the surface of the bathtub, and at the same time, do not let cigarette butts or heat sources higher than 70°C touch the surface of the bathtub.
7. Do not use rough surfaces and utensils containing chemical solvents or particles to clean the surface of the cylinder body.
8. If the water return device and the nozzle are blocked by hair and other sundries, they can be unscrewed and cleaned.
bathtub repair
9. Do not use hot water higher than 80 degrees. Repeated use of hot water will reduce the service life of the cylinder. The correct way is to put cold water first and then hot water
10. Do not start the water pump when there is no water in the bathtub
11. During the hydromassage, pay attention to avoid sundries or other objects from blocking the water return port, which will cause excessive load on the water pump, cause the water pump to overheat and burn out the water pump.
2. Bathtub Maintenance Instructions
bathtub cleaning
Nowadays, the bathtubs on the market are generally made of acrylic, steel plate, and cast iron. Among them, the acrylic bathtub has rich shapes, good heat preservation effect and easy to clean, but its surface hardness is low, and the surface is easy to be scratched; and the steel plate Although the surface of the bathtub is smooth, it is not resistant to impact and is easily cracked;
The cast iron bathtub is relatively bulky, and it is easy to be knocked out of the crack during the handling process. Regardless of the bathtub, various conditions will appear after a long period of use.
Due to the high cost of the bathtub, the sale value on the market is also high, so facing a series of problems, it is generally not replaced, but the bathtub is repaired.
3. Common faults of bathtubs
Bathtub cleaning and maintenance
Bathtub maintenance is carried out for different faults, and the common faults of the bathtub include: 1. The bathtub cannot enter water; 2. The bathtub leaks; 3. The bathtub is not powered or the leakage protection switch trips; 4. The bathtub massage water cannot be adjusted. 5. The bathtub control panel cannot be started.
This is the most common failure of the bathtub, and the fourth and fifth points are for the failure of the jacuzzi. Different failures require different maintenance methods.
Fourth, the method of bathtub maintenance
bathtub repair
The method of repairing the bathtub corresponds to the fault one by one. If the bathtub does not enter the water, it is usually because the faucet is blocked by foreign objects, so the maintenance method is to clean up the foreign objects; the repair method for the bathtub leakage is to check whether the faucet valve core and sealing rubber ring are damaged Then just replace it; if the massage bathtub is not powered on, it is usually due to poor contact of the power line or leakage of the power circuit, and it can be repaired accordingly;
If the water power of the jacuzzi cannot be adjusted, it is likely that the suction of the water pump is not enough and needs to be checked and repaired, or the nozzle is blocked, and it can be restored to normal after dredging.
Five, bathtub crack repair
bathtub cleaning
The reasons for bathtub cracks are divided into cold cracks, hot cracks, and impact cracks, but no matter what kind of cracks are caused, the crack repair methods are the same.
If the cracks are serious, it is recommended to ask professionals to repair them; for small cracks, you can use the adhesive of the corresponding bathtub material for bonding, of course, you must choose an adhesive that is non-toxic and harmless to the human body.
After the bathtub is cleaned and wiped dry, the adhesive can be used. After it is dry, it can be tested to see if there is any water leakage. If there is no water leakage, it can be put into normal use.