For the aesthetics of the interior decoration, the bathroom ceiling is essential, and there are various decoration methods for the bathroom ceiling, so what problems should we pay attention to when choosing the bathroom ceiling? The following is a detailed introduction to the selection and installation of bathroom ceilings.
One: The things and skills that need to be purchased for the overall bathroom ceiling:
1. Lamp warmer: The material of the lamp surface is generally made of quartz hard glass, and specific manufacturers will use different types of quartz hard glass. When we choose, we mainly look at whether the surface of the lamp is uniform. If the surface of the lamp is uneven, it may cause an explosion. One is to see if the joint between the double thread and the lamp body is tightly combined.
2. Ventilation: The bathroom is a relatively humid environment when taking a bath. Generally, the ventilation fan has 2 gears. The high gear can quickly remove the water vapor in the bathroom, and the low gear is mainly used to eliminate the peculiar smell in the bathroom.
The most important thing about the ventilation fan is to see the noise of the motor. The general motor is an oil-impregnated bearing, which belongs to sliding friction, which will generate relatively large noise and resonate with the ceiling. Some brands of motors use ball bearing motors, which belong to rolling friction, and the friction resistance is smaller than sliding friction. It is characterized by low noise, which is lower than the current international standard, and the other is long service life.
3. Air heating: Air heating depends on the blowing system, whether it can send hot air to 1.8-2M, because the air supply requirements of general air heating must reach the range of 1.8-2M. This can make the user not feel that the temperature of the lower body is not enough when taking a bath.
4. The material of the bathroom gusset is aluminum, which can be divided into three categories: sanding, rolling coating and film coating in terms of technology. Frosting is directly drawn on the aluminum material, and the surface is oxidized. This process can avoid rust. Roller coating requires 3 rolls and 3 coats in the production process. In layman’s terms, it means sticking the film 3 times and rolling it 3 times. The production process of the film-coated board is made of imported PVC film and overcoated color paint. The surface pattern is rich in color and has the advantages of anti-wear, stain resistance, and convenient scrubbing. Now there is also a kind of Taiyin board, which is a kind of anti-seepage and seepage board, a bionic technology, just like the lotus leaf, the water droplets will not condense on it, but will roll down directly.
Two: Overall bathroom ceiling construction and installation:
Gussets are divided into light and dark colors in terms of color. As for how to choose a color, it depends on your preference to match your bathroom. Turn on the corresponding equipment switch to test the machine first. If the light is warm, you have to turn it on for 15 seconds to feel whether there is heat. If there is, then there is no problem. After the fan heater is turned on, feel whether there is hot air at a place 1.8-2m away from the fan heater. If there is, it proves that the fan heater is normal.
Turn on the high and low gears of the ventilation fan to listen to the noise level, whether the noise is relatively quiet, and whether there is any strange sound. The buckle plate depends on whether it is flat at the seam of the electrical appliance, and whether the overall assembly line is smooth.
In terms of installation of the overall bath roof, the distance from the ground is required to be between 2.3-2.5 meters, which is the best effect for heating. If the height is too low, it will burn the top of the user’s head. Check whether the entire ceiling is flat, and the electrical appliances should be staggered with the pipes to ensure the appearance, and the pipes should be sealed in the ceiling as much as possible. This kind of installation is usually free of charge by the store, but if there is a special-shaped installation, it will be charged A certain amount of special-shaped installation process costs. The so-called special-shaped installation means that the pipes in some bathrooms may be very special, protruding a lot downwards, and they must be packaged at corners to achieve the appearance as much as possible.
Precautions for installation of ceiling in bathroom
1. The purchased aluminum gusset and the matching keel and accessories should meet the product quality requirements and must not be bent or deformed.
2. The bathroom is a place for bathing and washing. The ceiling of the bathroom should be made of metal, plastic and other materials.
3. When installing the aluminum gusset plate, if there is a deviation in size, it should be adjusted first and then inserted in order. Hard insertion is not allowed to prevent deformation.
4. Large lamps, exhaust fans, etc. should be fixed on the keel alone, and should not be placed directly on the aluminum buckle.
5. When suspending the ceiling of the bathroom, pay attention to the opening of the bathroom heater (there is no need to consider so much for the square gusset).
The above are related questions about the purchase and installation of bathroom ceilings shared with you, and I hope they can be helpful to you.